All stock codes associated to this product
POE2000SC
Overview
The POE2000SC Gigabit Ethernet PoE Media Converter, a
POE2000 Series model, has a 10/100/1000Mbps PoE RJ-45 and a SC terminated
multimode fibre port. Use to power PoE PD devices such as IP Phones and support
copper-to-fibre media conversion.
The POE2000SC Gigabit Ethernet PoE Media Converter is a dual purpose
device. It supports media conversion applications between Gigabit Ethernet
10/100/1000Base-T over UTP/STP copper cable and SC terminated 1000Base-SX over
multimode fibre cable, supporting ranges of up to 550 metres. The device also
supports IEEE 802.3af compliant Power over Ethernet (PoE) applications, and can
be used to power PD (Powered Device) PoE equipment such as IP phones and IP
cameras via UTP or STP data cable.
The POE2000SC is a model from Alloy's
POE2000 Series of PoE Media Converters. As a Media Converter, models in the
series support most types of Gigabit media conversion, including 10/100/1000Mbps
RJ-45 copper to 1000Base-SX multimode fibre (with either LC, SC or ST
connectors, maximum link range of 550 metres), 10/100/1000Mbps RJ-45 copper to
1000Base-LX singlemode fibre (LC or SC connectors for 10, 30 or 50Km ranges),
10/100/1000Mbps RJ-45 copper to SFP providing 1000Base-SX/LX singlemode fibre
(via SFP slot installed mini-GBIC modules), and 10/100/1000Mbps RJ-45 copper to
1000Base-LX WDM singlemode/singlecore fibre (SC connector, 20Km range).
The PoE capability of POE2000 Series Media Converters is comprehensive;
as a PSE device, all models support signature sensing, power monitoring
functions including PD discovery, classification and current limiting, PD
power-out auto-detection, PD over and under current power protection, fault
protection input, minimum load sensing and PSE MDI power enable / disable. All
models automatically discover PD PoE devices, power them over UTP data cable to
a maximum of 15.4 watts, monitor power supply, indicate operating and fault
status via a comprehensive LED suite, and protect from power
faults.
POE2000 Series Converters also support Link Fault Passthrough in
both Far-end-Fault (FEF) and Forced Modes (FM). LFP allows these Media
Converters to monitor both the fibre and copper RX ports for signal loss. In the
case of a loss of RX signal on one media port, the Converter will automatically
disable the TX signal to the other media port, thus passing through the link
fault LED status. FEF mode enables the Converter to stop sending a link pulse to
a LFP capable Converter on the other end of the cable; the link partner
Converter will synchronously stop sending data, preventing loss of valuable data
transmitted over an invalid link. Combining FM and FEF LFP functions supports
troubleshooting and network security capability, as both end devices can be
notified of a loss of fibre link and a managed switch connected to a POE2000
Series Converter can be configured to diasable the link and notify
administrators of the event.
Features
- Power PoE PD devices such as IP Phones, IP Cameras over UTP data cable
- IEEE 802.3af PoE (Power over Ethernet) PSE compatible
- Comprehensive PoE functions: PD Signature Sensing, power monitoring and
current protection
- Supports Gigabit media conversion: copper-to-fibre and mutimode/singlemode
fibre-to-fibre
- 10/100/1000Mbps auto-negotiation on RJ-45 copper port
- Maximum fibre link ranges: 50kms (fixed fibre port models), 20Kms (WDM
models) or 120 Kms (SFP model)
- Supports 100Base-T and 100Base-TX copper-to-fibre media conversion
- LC, SC and ST fixed fibre port connector models
- Flexible SFP fibre interface model - install Alloy or third party
mini-GBIC modules
- WDM models for 1000Base-LX singlemode/singlecore media conversion
- Far-End-Fault and Forced mode LFP supports easy link fault monitoring and
auto link shutdown
Specifications
Standards Compliance
- IEEE802.3af Power over Ethernet
- IEEE 802.3 10Base-T specification
- IEEE 802.3u 100Base-TX specification
- IEEE 802.3ab 1000Base-T specification
- IEEE 1000Base-SX Gigabit Ethernet fibre specification
- IEEE 1000Base-LX Gigabit Ethernet fibre specification
- IEEE 802.3x full-duplex flow control specification
Interface/Protocol/Wavelength/Range Specifications
- POE2000SC: RJ-45 PoE 1000Base-T to 1000Base-SX (SC), multimode fibre,
850nm, max range 550m
RJ-45 Port
- 10/100/1000Mbps throughput
- NWay auto-negotiation
- Auto-MDIX Full/Half-Duplex transmission
- IEEE 802.3af compliant PoE
Fibre Optic Ports
- 1000Mbps throughput
- Auto-negotiation Transmission: Full-duplex only
WDM Models
- 1000Mbps throughput
- Auto-negotiation
- Transmission: Full-duplex only
- Single core of singlemode fibre cable used
- TX and RX 1310/1550nm datastreams multiplexed on a single fibre core
- A pair of POE2000SC3.20 and POE2000SC5.20 Converters must be used at
either end of the fibre link or:
- One POE2000SC3.20 (1310nm Tx) or POE2000SC5.20 (1550nm Tx) and a suitable
wavelength device at other end of link
Cable Types Supported
- RJ-45 Port: UTP or STP Cat 5 or higher (must be Cat 5 or higher in Gigabit
Ethernet networks)
- SFP Slot (SFP model): fibre cable type determined by installed mini-GBIC
Transceiver module
- LC/SC/ST Ports (multimode models): 50/125µm, 62.5/125µm or 100/140µm
- LC/SC/ST Ports (singlemode/WDM models): 8.3/125µm, 8.7/125µm, 9/125µm or
10/125µm
Power over Ethernet Specifications
- Power over Ethernet Specifications
- IEEE 802.3af Power over Ethernet compliant
- PSE (Power Sourcing Equipment) functionality
- PD Class 0 (0.44 to 13 watt supply)
- PD Class 1 (0.44 to 3.8 watt supply)
- PD Class 2 (3.8 to 6.5 watt supply)
- PD Class 3 (6.5 to 13 watt supply)
- Signature sensing
- Power monitoring functions including PD (Powered Device) discovery,
classification, current limiting etc
- PD Power-out auto-detection
- PD Over-current and Under-current power protection functions
- Fault Protection Input Minimum load sensing
- PSE MDI power enable/disable
LFP (Link Fault Passthrough) Functions
- LED status propagation
- Far End Fault mode supported: link pulse to link partner terminated on
loss of the fibre RX signal
- Forced mode supported: TX signal auto-disabled, LED link fault status
propagated
Other Functions
- Jumbo frame (Normal Mode: 2KB, Cut-Through Mode: 9KB)
DIP Switch Configuration
- IP 1: LFP Enabled/LFP disabled
- DIP 2: PoE Enabled/PoE disabled
- DIP 3: Bridge Mode enabled/Cut Through Mode enabled
LED Indicators
- PWR: Green, lit when +5V power source active
- FX LNK/ACT: Lit - fibre port link good; Blink - fibre traffic is present
- TP LNK/ACT: Lit - TP link good; Blinks - TP traffic is present
- TP SPEED: Green Lit - TP speed 1000Mbps; Yellow Lit - speed 100Mbps; Off -
speed 10Mbps
- PoE PSE-TP: Green Lit - PoE power supply active; Red Lit - PoE power
supply disrupted
- 4W: Green Lit - supplying PD Class 1 power
- 7W: Green Lit - supplying PD Class 2 power
Power
- 100-240VAC, 47 63 Hz internal power supply
- Maximum consumption: 19W
Electromagnetic Compatibility
- FCC Part 15 Class A, CE Mark, C-Tick
Mechanical
- Form Factor: Standalone Desktop all-metal case
- Dimensions: 133mm x 158mm x 40mm (D x W x H)
- Weight: 750 grams
Environmental Specifications
- Temperature: 0 Degree to 50 DegreeC (Standard Operating) =
- Humidity: 5% to 90% (Standard operating)
Networking
