All stock codes associated to this product
QXPW6AX200, QXP-W6-AX200, QN99796
QNAP QXP-W6-AX200
Overview
Upgrade to Wi-Fi NAS or Wi-Fi Windows/Linux PC by Adding 802.11ax high-speed
wireless connectivity.
The QXP-W6-AX200 is a PCIe Gen 2x1 Wi-Fi 6 wireless adapter with an Intel
Wi-Fi 6 AX200 module that supports the IEEE 802.11ax standard (backwards
compatible with 802.11a/b/g/n/ac), MIMO 2Tx2R, MU-MIMO TX/RX and Bluetooth 5.0.
The QXP-W6-AX200 can be installed in a QNAP NAS, or Windows/Linux PC to provide
fast Wi-Fi 6 connection speeds. The QXP-W6-AX200 can also be used with Wi-Fi 6
router to deploy Wi-Fi 6 network environment. A full-height bracket is
pre-installed on the QXP-W6-AX200 and two low-profile brackets are also
included.
- The QXP-W6-AX200 supports Wi-Fi 6 802.11ax, provides up to 2400Mbps
connection speeds, and is backwards compatible with 802.11acR2/
abgn.
- The QXP-W6-AX200 supports MU-MIMO 2Tx2R, providing greater connectivity
with multiple clients; OFDMA increases network efficiency and decreases packet
delay.
- The QXP-W6-AX200 has dual band 2.4GHz/ 5GHz antennae, multiple angle tilt,
and a magnetic base for the best signal strength direction and
location.
- The QXP-W6-AX200 supports BSS coloring that marks shared frequencies with
a number for easy differentiation.
- Bluetooth 5.0 provides faster speeds and wider range to easily connect to
multiple devices.
- Notes: Bluetooth 5.0 is only available when installed in a Windows PC and
requires an internal USB connection.
- Wi-Fi 6 uses 1024-QAM to provide a signal packed with more data, and
enables 25% faster data rates than 256-QAM.
Specifications
Controller |
Intel
AX200 wireless module |
PCIe
and Lanes |
PCIe
Gen2 x1 |
Theoretical
maximum performance |
2.4Gbps
(5GHz) |
Antenna |
2T
x 2R |
Supported
operating systems |
QTS
4.4.3 or later; 64-bit Windows 10 PC download and install
[driver(https://downloadcenter.intel.com/en/product/189347)] from Intel
website; Linux kernel 5.1 or later download and install
[driver(https://www.intel.com/content/www/us/en/support/articles/000005511/network-and-i-o/wireless.html)]
from Intel website |
Hardware
requirement |
NAS
or PC with a PCIe slot, 64-bit processor and operating
system. |
Package
Contents |
1
x QXP-W6-AX200 card (GC-WBAX200 QNAP edition, a full-height bracket is
pre-installed); 1 x installation guide; 2 x half-height low-profile
brackets (a standard bracket and a flat bracket for NAS); Windows 10
driver CD. |
Operating
Temperature |
0C
~ 40C (32F ~ 104F) |
NAS
Software Spec |
Supports
QTS 4.4.3 or later |
Security
Protocol |
No
Auth / WEP / WPA-Personal / WPA2-Personal |
Supports
the Captive Portal authentication method: |
Access
WiFi via the configuration by Qfinder utility / Browser
Station. |
Note |
System
requirements: 64-bit x86-based NAS (Intel and AMD), or ARM-based NAS, with
QTS 4.4.3 (or later) with a PCIe Gen 2x1slot. Check the [Compatibility
List(https://www.qnap.com/en/compatibility/)] for a full list of
compatible NAS. |
Some
NAS models must update their BIOS to the following versions. You can
download BIOS from the [Download Center(https://www.qnap.com/en/download)]
and learn [how to update a BIOS
here(https://www.qnap.com/en/how-to/tutorial/article/updating-the-bios-on-a-qnap-nas)]. |
TS-251B:
Q015AR02 |
TS-653B:
QY59AR58 |
TS-251D,
TS-253D: Q04WAR08 |
TS-453D,
TS-653D: Q04MAR12 |
TS-453DU,
TS-453DU-RP, TS-853DU-RP, TS-1253DU-RP:
Q05PAR03 |