All stock codes associated to this product
SD7SB6S128G, SD7SB6S-128G, SANSD7SB6S128G1122
Sandisk X300 SSD (Solid State Disk)
Reliable And Responsive Performance With Low Power
Based on state of the art 1Ynm TLC flash technology, the SanDisk X300 SSD delivers performance with high reliability and low power. It features nCache 2.0, SanDisks next generation tiered caching technology, designed to improve SSD responsiveness for most corporate and consumer workloads.
The X300 is highly versatile and can accommodate a wide range of computing platforms. It is available in 2.5 7mm cased, M.2 2280, and mSATA form factors with capacities of 128GB, 256GB, 512GB, and 1TB.
X300 KEY FEATURES
NCACHE 2.0 IMPROVES SSD
RESPONSIVENESS FOR HIGH PRODUCTIVITY WORKLOADS
ON CHIP COPY (OCC) OFFLOADS WORK FROM CONTROLLER AND DDR RESOURCES TO IMPROVE PERFORMANCE
MULTI PAGE RECOVERY (MPR) - PROVIDES AN ADDITIONAL LAYER OF DATA PROTECTION USING PAGE-LEVEL STRIPING WITH DISTRIBUTED PARITY
LOW POWER WITH DEVSLP SUPPORT AND INSTANTGO COMPATIBILITY
UP TO 1TB CAPACITIES IN 2.5 7MM, M.2 2280, AND MSATA FORM FACTORS
TESTED FOR >72 TBW (128GB) AND >80 TBW (256GB-1TB)
SATA REVISION 3.2 6GB/S INTERFACE
WINDOWS WHCK CERTIFIED
DYNAMIC THERMAL THROTTLING
nCache 2.0 Technology
nCache 2.0 uses a combination of both SLC and TLC flash blocks to improve endurance, increase efficiency, and boost performance. By first writing all of the data to SLC blocks, the write amplification on the TLC blocks is minimized. The new On Chip Copy (OCC) mechanism then independently copies the SLC cache blocks into the TLC blocks in main storage, thus offloading the burden from the controller and DDR resources. This leaves the DRAM cache and controller free for other tasks.
Reliability
The X300 SSD also includes a new and robust on-the-fly error handling mechanism called Multi-Page Recovery (MPR). It uses page-level striping with distributed parity for an added layer of data protection and can recover errors that other traditional error correction mechanisms cannot.
Low Power
The X300 utilizes a SATA DEVSLP low-power mode, compatible with Microsoft InstantGo, to minimize its power consumption during idle periods. DEVSLP enables the SSD to completely shut off its SATA PHY, thus resulting in much lower power consumption compared to SATA Slumber. This increases the amount of usable hours per battery charge, which is essential for modern mobile devices.
TCO
SanDisk SSDs are more reliable than HDDs, which can improve total cost of ownership (TCO) by reducing downtime due to hard drive failures. They also offer lower latency and greater read/write speeds over traditional HDDs1, so users may experience a noticeable improvement in responsiveness. IT departments can extend the useful life of their PC inventory by upgrading the HDDs to the X300 SSD, thus prolonging replacement cycles and maximizing asset value.
Specifications
|
|
|
|
|
|
| Capacity1 |
1TB |
512GB |
256GB |
128GB |
| Sequential Read/Write2 |
Up to 530/470MB/s |
Up to 530/470MB/s |
Up to 530/470MB/s |
Up to 530/470MB/s |
| Random Read/Write2 |
Up to 90/74k |
Up to 90/74k |
Up to 90/74k |
Up to 90/74k |
| Form Factor3 |
2.5" 7mm cased, m.2 2280, mSATA |
2.5" 7mm cased, m.2 2280, mSATA |
2.5" 7mm cased, m.2 2280, mSATA |
2.5" 7mm cased, m.2 2280, mSATA |
| Interface |
SATA Revision 3.2 (6 Gb/s) backward compatible to SATA Revision 2.0 (3 Gb/s) and SATA Revision 1.0 (1.5 Gb/s) |
SATA Revision 3.2 (6 Gb/s) backward compatible to SATA Revision 2.0 (3 Gb/s) and SATA Revision 1.0 (1.5 Gb/s) |
SATA Revision 3.2 (6 Gb/s) backward compatible to SATA Revision 2.0 (3 Gb/s) and SATA Revision 1.0 (1.5 Gb/s) |
SATA Revision 3.2 (6 Gb/s) backward compatible to SATA Revision 2.0 (3 Gb/s) and SATA Revision 1.0 (1.5 Gb/s) |
| Endurance |
>80 TBW |
>80 TBW |
>80 TBW |
>65 TBW |
